Disclaimer: This is an example of a student written essay.

Any opinions, findings, conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of UKEssays.com.

Fiber Optic Sensing Technologies for Bridge Health Monitoring

 ✅ Paper Type: Free Essay ✅ Subject: Technology ✅ Wordcount: 4105 words ✅ Published: 23rd Sep 2019

Abstract

The application of structural health monitoring (SHM) systems in bridge infrastructures has lead to the enhanced safety, durability, reliability and cost-effective management of these structures. In the last two decades, a significant number of innovative sensing technologies based on optical fiber sensors have been applied for SHM due to their inherent distinctive advantages, such as small size, light weight, immunity to electromagnetic interference (EMI) and corrosion, and embedding capability. Fiber optic-based monitoring systems use quasi-distributed and continuously distributed sensing techniques for real time measurement and long term assessment of physical and engineering properties of bridges. This allows for early stage damage detection and characterization, leading to timely remediation and prevention of catastrophic failures. The purpose of this article is to review the current state-of-the-art of fiber optic sensing/monitoring technologies, including the basic principles of various optical fiber sensors, novel sensing and computational methodologies, and the practical application status of this technology for bridge health monitoring. Additionally, application of these technologies to monitor temperature, inclination, stresses, strain measurements, vehicle speeds and weights, and corrosion and cracking of reinforced and prestressed concrete structures of bridges will also be discussed.

1. Introduction

Bridges play a vital role in advancing nation’s transport infrastructure. Loss of lives and financial losses have been caused by bridge failures (Li, Ou, and Zhou 2009). Bridges deteriorate with age and early detection of damage helps in  timely remediation preventing catastrophic failures. Several bridges built decades ago are now subjected to various load patterns and environmental changes, which can cause localized distress and if not corrected can result in bridge failure. Therfore, structural health monitoring is necessary to ensure bridge safety. SHM refers to the procedure used to assess the condition of structures over a period of time using appropriate sensors to monitor their performance, and measurements yeilded by these sensors can help in early damage detection and risk assessment, thus increasing reliability, safety and efficiency of the structures.

Recent advancements in fiber optic sensing (FOS) techniques offer unique advantages for i) long-term monitoring, ii) large distances (in the range of several kilometers), and iii) early detection of risks associated with damage of civil infrastructures. One of the distinct advantages of FOS is their ability to measure physical quantities (such as displacements, inclination and strains) continuously distributed over the full length of the fiber. In order to measure distributed strains over the full

length of a fiber, several techniques have been proposed, including Fiber Bragg Gratings (FBG), scattering based distributed sensors following the principle of optical reflectometry and interferometry (Fabry-Perot (FP)) based sensors. These sensing systems are easy to install, capable of autonomous operation, and are designed to measure strains and other physical parameters induced due to mechanical and thermal stresses. The objective of this paper is to review the current state-of-the-art of FOS technologies and its application for monitoring bridge infrastructures and its associated components.

2. Fiber Optic Sensing Technologies

A fiber optic sensing system consists of a light transmitter, a receiver, an optical fiber, a modulator element, and a signal processing unit. These systems are based on the variations of physical characteristics of optical fibers such as light intensity, frequency/wavelength, phase, and polarization, which are sensitive to various external signals/stimuli. Based on the sensing principle, fiber optic sensors can be categorized into different types as illustrated in the following sections.

2.1 Fiber Bragg Grating (FBG) Sensors

FBG sensors consist of varied refractive indices in the core of optical fiber (Peters 2009). According to Bragg’s law, a beam of white light is written in the FBG sensor, and when the light from the broadband source passes through the grating at a particular wavelength, the Bragg wavelength is reflected which is related to the grating period, as shown in Figure 1. The Bragg wavelength can be calculated by equation 1, where eff is the effective index of refraction and Λ is the grating period. Bragg wavelength could be shifted with the variations of temperature, strain, and vibration due to the surrounding environment. The variation of the Bragg wavelength can be obtained by equation 2, where Δ is the strain variation, Δ is the temperature change, is the coefficient of the thermal expansion, is the thermooptic coefficient, and is the strain-optic coefficient.

Figure 1. Working principle of FBG Sensor

${\lambda }_{B}=2{n}_{\mathit{eff}}\mathrm{\Lambda }$

(1)   $\mathrm{\Delta }{\lambda }_{B}={\lambda }_{B}\left[\left(\alpha +\xi \right)\mathrm{\Delta }T+\left(1–{p}_{e}\right)\mathrm{\Delta }\epsilon \right]$

(2)

2.2 Optical Time-Domain Reflectometry (OTDR) Sensors

An OTDR based sensor is capable of distributed sensing over the length of an optical fiber with a specific refractive index (Barnoski et al. 1977). When a light pulse at a particular wavelength propagates along the optical fiber, the sensor can locate the position of the interaction according to the propagation time, as shown in Figure 2. The OTDR-based distributed sensor measures the change in the properties of the light along the entire optical fiber by measuring the time of flight of the returned pulses. The Brillouin optical time domain reflectometer (BOTDR) is one of the well-known distributed fiber optic sensors that is based on the Brillouin scattering. Due to the advantage of being capable of measuring continuous strain and temperature over a long distance, the BOTDR has been widely applied in distributed monitoring of large-scale civil structures.

Figure 2. Working principle of OTDR Sensor

2.3 Fabry-Perot Interferometry (FPI) Sensors

FPI sensors follow the principle of Fabry-Perot interferometry (Yoshino et al. 1982), which is the intensity of the interference signals illuminated between two parallel reflecting interfaces as shown in Figure 3. The interference pattern shifts according to the optical path change and depending on the length of FP cavity. The length can be affected by pressure change and temperature variation (e.g. environmental change). For FPI sensors, the intensity of interference signal is given by equation 2, where I1 and I2 are the reflection at the cavity reflecting interfaces, φ is the initial phase of the interference, Λ is the optical wavelength and Z is the optical path difference (Rao 2006).

Figure 3. Working principle of FPI

Sensor

$I=2{I}_{1}{I}_{2}\sqrt{{I}_{1}{I}_{2}}×\mathrm{cos}\left(4\mathit{\pi Z}/\lambda +\varphi \right)$

(3)

3. Applications of Fiber Optic Sensing Technologies for Bridge Health Monitoring

Bridges are critical infrastructures which are vital for daily transportation activities and its health conditions have always been a concern for the bridge owners, contractors and government. Moreover, bridges are subjected to various environmental and operational loadings and continuous real time monitoring is necessary for system identification, damage detection, safety condition assessment, and structural performance prediction. Due to unique and distinctive advantages, fiber optic sensors have been meticulously explored as an effective tool for monitoring various structural components of bridges (decks, towers, stay cables, suspenders, girders, piers, piles, and abutments), for measuring different physical parameters such as strains, temperatures, accelerations, deflections/displacements, cracks, and corrosion detailed in the following sections.

3.1 Comprehensive Bridge Monitoring

Numerous fiber optic based SHM systems have been developed and effectively deployed on various bridges worldwide. Barbosa et al. developed novel weldable strain and temperature sensors based on FBG and installed on circular pedestrian steel bridge for loading tests and evaluate the real time variations of the axial forces in its main structural elements (Barbosa et al. 2008). Mehrani et al. developed a remote sensing system utilizing fiber optic sensors based on FPI for condition assessment of bridge by monitoring its behaviour under traffic loads (Mehrani, Ayoub, and Ayoub 2009). The system was deployed for field instrumentation on a bridge in Florida, USA, during its construction stage. The accuracy of the sensors was estimated by static and dynamic testing under heavy truck loads and validated through 3-dimensional analytical finite element analysis. Kerrouche et al. developed a low cost and compact FBG-based monitoring system incorporating a scanning Fabry Perot filter for strain measurement (Kerrouche et al. 2009). The performance of the system was validated in a field test by installing sensors into CFRP reinforcement rods of a damaged bridge. Rodrigues et al. developed an FBG-based system with embedded displacement and strain transducers for long-term monitoring of structural performance of concrete bridges which was applied to a concrete bridge (Rodrigues et al. 2012). Glisic and Inaudi developed a novel method using distributed fiber optic technology based on Stimulated Brillouin scattering for integrity monitoring of bridges to detect cracks and local deformations (Glisic and Inaudi 2012). The method utilized a glass fiber reinforced thermoplastic composite tape integrated with polyimide-coated optical fibers and deployed on-site by attaching on concrete slab and steel girders of a 1000m long bridge in order to detect and localize cracks and unusual short-term and long-term strain changes. Mokhtar et al. designed a compact temperature compensated FBG based strain sensors sandwiched between two polypropylene slabs and installed on the paragrid and on the surfaces of a flexi-arch bridge to monitor strain and temperature (Mokhtar et al. 2012). Surre et al. developed an optical fiber sensor system based on FBG for long-term strain monitoring and condition assessment of a redundant 50-year-old concrete footbridge (Surre, Sun, and Grattan 2013). Yau et al. developed a simple, inexpensive, and practical method based on FBG strain and tilt sensors to measure vertical displacements of bridges (Yau et al. 2013). An inclination approach and a curvature approach using these sensors was employed to determine vertical displacements with various support conditions and varying stiffness (EI) along the spans of the bridge which is further validated through numerical simulations. Zhao et al. developed multiscale fiber optical sensing network by combining distributed optical fiber sensing technology based on Brillouin scattering and the FBG sensing technology for bridge strain monitoring with local high precision and distributed high precision respectively (Zhao et al. 2012). Minardo et al. demonstrated stimulated Brillouin scattering based distributed FOS for monitoring strain distribution along a 44.4 m long road bridge (Minardo et al. 2012). The optical fibers were installed along the supporting beams and the results yielded a spatial resolution of 3 m and a strain resolution of 15 µε. Xu et al. investigated field monitoring of a 1108 m suspension bridge using integrated distributed FOS based on high resolution Brillouin time domain analysis system with differential pulse-width pair (DPP) technique (Xu et al. 2016). The system monitored distributed strains along the whole length of the bridge with up to 0.05 m spatial resolution, and 0.01 m/point sampling interval.

3.2 Bridge Cables and Suspenders Monitoring

Cables and suspenders are one of the most critical structural components of a bridge that readily suffer from fatigue damage, corrosion damage, and their coupled effects (Lan and Li 2009). Li et al. developed a self-sensing smart stay cable assembled with FBG strain and temperature sensors incorporated into a glass fibre reinforced polymer (GFRP) bar (Li, Ou, and Zhou 2009). The system was inserted into the hollows of steel wires and fixed with the steel cable to monitor deformation, stress and fatigue within the cable. The efficiency of the developed smart stay cable was proved through field application by evaluating the induced stresses and fatigue accumulative damage of a stay cable bridge in China (Li, Zhou, and Ou 2011). He et al. designed a cable force monitoring system by combining local high precision FBG sensors and full scale distributed BOTDR sensing technique in one single optical fiber and installed along with the steel cable wire (He, Zhou, and Jinping 2013). The cable force obtained from the developed sensor agreed well with theoretical value with relative error less than ± 5%. Hu et al. conducted an indirect measurement study for cable force monitoring by developing a FBG vibration sensor for online monitoring of the cable vibration characteristics (Hu et al. 2017). The sensor was deployed on Tongwamen bridge, China and the monitored vibration frequency was converted into cable force according to the theory of string vibration in order to achieve an indirect measurement of bridge cable force.

3.3 Railway Bridge Monitoring

Scott et al. evaluated a FOS system based on commercially available FBG for strain monitoring in railway bridges by conducting laboratory tests under the bridge loading conditions (Scott et al. 2013). The experimental results showed that the FBG strain sensor can obtain good agreement compared with electrical resistance strain gauges. Wei et al. designed a FOS system based on FBG to monitor the bridge strengthening effect accurately by measuring vertical deflection, dynamic load moment and transverse vibration of the railroad bridge (Wei et al. 2013). Wei concluded that the developed system can be extended to large span and arch bridges. Yoon et al. utilized Brillouin optical correlation domain analysis (BOCDA) technology to monitor the longitudinal strain on the rail and girders of a railway bridge during train passage in real time (Yoon et al. 2016). The performance of BOCDA in measuring distributed strain was comparable with conventional strain gauges. Yu et al. developed an SN model of a typical heavy haul railway bridge of China high speed railway and designed a FBG-electrical based multi-sensor for fatigue load monitoring (Yu et al. 2018). The multi-sensor consisted of a fiber-reinforced polymer optical FBG, an electrical resistance strain gauge, a linear variable displacement transducer, and an accelerometer.

4. Conclusions

This paper provides a brief review of various fiber optic sensing technologies employed for structural health monitoring of bridges. Bridges are an integral part of society’s infrastructure and reliable sensing methods are necessary to monitor them and ensure their safety and efficiency. FOS technology has proven to be a suitable method for this purpose and possesses several distinct advantages over other monitoring methods. The simplicity, immunity to EMI and corrosion, distributed long-range sensing, non-invasive sensing (due to the miniature size of FOS), and signal sensitivity of FOS systems enable them to become a popular and effective structural health monitoring approach. However, certain challenges and limitations of FOS such as fiber handling issues, bending losses, cross-sensitivity between thermal strain and mechanical strain exists and still needs to be addressed. In conclusion, FOS have shown a promising potential over other conventional methods in the monitoring of bridge infrastructure.

5. References

• Barbosa, C, N Costa, LA Ferreira, FM Araújo, H Varum, A Costa, C Fernandes, and H Rodrigues. 2008. ‘Weldable fibre Bragg grating sensors for steel bridge monitoring’, Measurement Science and Technology, 19: 125305.
• Barnoski, M_K, M_D Rourke, SM Jensen, and RT Melville. 1977. ‘Optical time domain reflectometer’, Applied Optics, 16: 2375-79.
• Glisic, Branko, and Daniele Inaudi. 2012. ‘Development of method for in-service crack detection based on distributed fiber optic sensors’, Structural Health Monitoring, 11: 161-71.
• He, Jianping, Zhi Zhou, and Ou Jinping. 2013. ‘Optic fiber sensor-based smart bridge cable with functionality of self-sensing’, Mechanical Systems and Signal Processing, 35: 84-94.
• Hu, Dongtao, Yongxing Guo, Xianfeng Chen, and Congrui Zhang. 2017. ‘Cable force health monitoring of Tongwamen Bridge based on fiber bragg grating’, Applied Sciences, 7: 384.
• Kerrouche, A, WJO Boyle, T Sun, and KTV Grattan. 2009. ‘Design and in-the-field performance evaluation of compact FBG sensor system for structural health monitoring applications’, Sensors and Actuators A: Physical, 151: 107-12.
• Lan, CM, and H Li. 2009. “Stay cable vehicle live load effects analysis based on structural health monitoring data.” In ICCES: International Conference on Computational & Experimental Engineering and Sciences, 75-82.
• Li, Dongsheng, Zhi Zhou, and Jinping Ou. 2011. ‘Development and sensing properties study of FRP–FBG smart stay cable for bridge health monitoring applications’, Measurement, 44: 722-29.
• Li, Hui, Jinping Ou, and Zhi Zhou. 2009. ‘Applications of optical fibre Bragg gratings sensing technology-based smart stay cables’, Optics and Lasers in Engineering, 47: 1077-84.
• Mehrani, Ebrahim, Ashraf Ayoub, and Amir Ayoub. 2009. ‘Evaluation of fiber optic sensors for remote health monitoring of bridge structures’, Materials and Structures, 42: 183-99.
• Minardo, Aldo, Romeo Bernini, Lucio Amato, and Luigi Zeni. 2012. ‘Bridge monitoring using Brillouin fiber-optic sensors’, IEEE Sensors Journal, 12: 145-50.
• Mokhtar, MR, K Owens, J Kwasny, SE Taylor, PAM Basheer, D Cleland, Y Bai, M Sonebi, G Davis, and A Gupta. 2012. ‘Fiber-optic strain sensor system with temperature compensation for arch bridge condition monitoring’, IEEE Sensors Journal, 12: 1470-76.
• Peters, Kara. 2009. ‘Fiber Bragg grating sensors’, Encyclopedia of structural health monitoring.
• Rao, Yun-Jiang. 2006. ‘Recent progress in fiber-optic extrinsic Fabry–Perot interferometric sensors’, Optical Fiber Technology, 12: 227-37.
• Rodrigues, Carlos, Filipe Cavadas, Carlos Félix, and Joaquim Figueiras. 2012. ‘FBG based strain monitoring in the rehabilitation of a centenary metallic bridge’, Engineering Structures, 44: 281-90.
• Scott, R. H., P. Banerji, S. Chikermane, S. Srinivasan, P. A. M. Basheer, F. Surre, T. Sun, and K. T. V. Grattan. 2013. ‘Commissioning and Evaluation of a Fiber-Optic Sensor System for Bridge Monitoring’, IEEE Sensors Journal, 13: 2555-62.
• Surre, Frederic, Tong Sun, and Kenneth T Grattan. 2013. ‘Fiber optic strain monitoring for long-term evaluation of a concrete footbridge under extended test conditionss’, IEEE Sensors Journal, 13: 1036-43.
• Wei, Yong Jiu, Jin Tao Zhang, Yun Long Zhang, Xiang Chun Xi, Kun Li, and Sheng Chun Liu. 2013. ‘Research on Evaluation Method of the Bridge Strengthening Effect Based on Fiber Optic Sensor’, Advanced Materials Research, 791-793: 1901-04.
• Xu, Jinlong, Yongkang Dong, Zhaohui Zhang, Shunlong Li, Shaoyang He, and Hui Li. 2016. ‘Full scale strain monitoring of a suspension bridge using high performance distributed fiber optic sensors’, Measurement Science and Technology, 27: 124017.
• Yau, Man Hong, Tommy HT Chan, DP Thambiratnam, and HY Tam. 2013. ‘Static vertical displacement measurement of bridges using fiber Bragg grating (FBG) sensors’, Advances in Structural Engineering, 16: 165-76.
• Yoon, Hyuk-Jin, Kwang-Yong Song, Chanyong Choi, Hee-Seoung Na, and Jung-Seok Kim. 2016. ‘Real-Time Distributed Strain Monitoring of a Railway Bridge during Train Passage by Using a Distributed Optical Fiber Sensor Based on Brillouin Optical Correlation Domain Analysis’, Journal of Sensors, 2016: 10.
• Yoshino, Toshihiko, Kiyoshi Kurosawa, Katsuji Itoh, and Teruzi Ose. 1982. ‘Fiber-optic Fabry-Perot interferometer and its sensor applications’, IEEE Journal of quantum electronics, 18: 1624-33.
• Yu, Zhiwu, Zhi Shan, Ju Yuan, and Xiao Li. 2018. ‘Performance Deterioration of Heavy-Haul Railway Bridges under Fatigue Loading Monitored by a Multisensor System’, Journal of Sensors, 2018: 14.
• Zhao, Xuefeng, Jie Lu, Ruicong Han, Xianglong Kong, Yanhong Wang, and Le Li. 2012. ‘Application of multiscale fiber optical sensing network based on Brillouin and fiber bragg grating sensing techniques on concrete structures’, International Journal of Distributed Sensor Networks, 8: 310797.

View all

DMCA / Removal Request

If you are the original writer of this essay and no longer wish to have your work published on UKEssays.com then please:

Related Services

Prices from

AED557

Approximate costs for:

• 1000 words
• 7 day delivery

Humanity University

Dedicated to your worth and value as a human being!

Related Lectures